| CM44 |
|
KNIFE CUTTING FOR LEATHER AND SYNTHETIC MATERIALS |
|
The knife cutting technology eliminates the cost of cutting dies while taking advantage of a direct connection to CAD systems to immediately begin production. To compete with die-cutting press productivity CM44 adopts a structure with two cutting heads and a conveyor belt which organizes the flow of operations through three separate areas: piece nesting, nested piece cutting, and cut piece removal. |
|
Without pause or change of workplace, the operator maintains full focus and concentration on nesting the pieces on the leather carried by the conveyor belt. In a compact area served by a powerful local vacuum system, two cutting heads share the work for maximum optimization of operations. Tool change is viable thanks to the complete rotation of the cutting heads, which feature an oscillating knife, marking pen, 4 cutting-dies and punch revolver located in a convenient and visible frontal position. The rear table collects large amounts of cut leather enabling the removal of cut leather without constant attention. WORK
AREA |
||||||||||||||||||||||||||
|
For synthetic materials, in one or more layers, the automatic nesting function can perform fast piece positioning. Therefore, the cutting heads are well exploited and the operator, freed from nesting operations, can fully focus on the collection of the cut pieces. |
||||||||||||||||||||||||||
|
LINK
TO CAD
|
| CM55 |
|
KNIFE CUTTING FOR LARGE SKINS AND WIDE MATERIALS |
|
WIDE SKINS AND LARGE MATERIALS The structure of the Comelz CM machines with conveyor belt and two cutting heads guarantees high productivity due to its simultaneous nesting, cutting and removing capability. In CM55, the continuity between nesting and cutting makes processing of large skins and large pieces easier. |
|
On CM55, two telescopic heads with extra arm extension operate on a wide and deep area, shared with the nesting. This unique solution allows full visibility and control of the entire work area without interfering with the shapes displayed by the two laser projectors. |
||||||||||||||||||||||||||
|
This single nesting-cutting area, measuring 2 x 1.5 m, overcomes the limitations of conveyor belt systems with consecutive and separated nesting areas, creating the conditions for a real continuous nesting for pieces of any size. |
||||||||||||||||||||||||||
|
WIDE SKINS AND LARGE MATERIALS Skins and materials of unlimited length are processed without interruptions using interactive or automatic nesting, while side pockets allow to cut even skins over 2 m wide. The control software provides sophisticated functions which optimize speed and quality of the processing and also includes a practical editor for CAD patterns, even in DXF format.
|
| CM44S |
|
KNIFE CUTTING FOR INSOLES AND SOLES |
|
CM44S is a high productivity system. Without cutting dies it can cut insoles, heel seats, soles, toe puffs, counters on cellulose material, cellolose material with reinforced strip (and/or foam and/or textile), fiber-board, leather, neolite, regenerated leather, salpa, thermoplastic, etc. CM44 has two cutting heads with oscillating knife and a conveyor belt. |
|
The conveyor belt allows for the parallel execution of automatic material loading, piece cutting, and piece recollecting phases. The cutting heads can work without interruptions in a highly productive cycle. Fast and robust, the cutting heads have an oscillating knife and a marking pen. They work independently from each other on an area 1500mm wide and unlimited depth, optimizing the cutting speed and the material consumption. |
||||||||||||||||||||||||||
|
The loader is equipped with multiple clamping devices (18 needles and 18 suction cups) that are individually software activated, a motorized sheet centering system, and a sheet movement system controlled by 5 brushless motors. It can load every sheet of material used in the insole or sole production and it is compatible with roll feeding. |
||||||||||||||||||||||||||
|
Patterns imported from CALIGOLA or even from other CAD systems (in dxf exchange format) are automatically nested. It is also possible to perform a manual nesting using a bright laser projector (to nest irregularly shaped materials like scraps of sheets or leather).
|
| P55 |
|
PUNCH CUTTING FOR PATTERNS AND INSOLES |
|
MULTI-TOOL HEAD WITH FAST CHANGE SYSTEM P55 exploits the strength of punch cutting through an exclusive bridge structure with independent and synchronized mobile carriages. This original solution eliminates length limitations of the cutting area and allows a continuous and productive work cycle: no cuts to remove waste material, piece removal by fall and with the possibility to cut sheets with unlimited length or in rolls. P55 is therefore an “automatic” punching machine that eliminates dead time and does not require constant presence of the operator to remove pieces and waste or for frequent loading of the material. |
|
INDEPENDENT
SOFTWARE |
||||||||||||||||||
|
Because of its versatility and productivity, P55 is suitable for various contexts, from series development for pattern making to samples and small-medium production of insoles. P55 cuts in single or multiple layers a great variety of materials including cardboard, fibreboard, various plastic materials and all rigid materials for insoles. |
||||||||||||||||||
|
MULTI-TOOL
HEAD WITH FAST CHANGE SYSTEM
|